How to use
- Enter the marking from the tire sidewall as Current tire size. Formats such as
225/45R17,225/45 ZR17 94WandP215/60R16are all read, with or without spaces, load index or speed symbol. - Enter the size you want to fit as New tire size.
- You immediately get the diameter difference, whether it is inside the common guideline, the actual speed for each speedometer reading and the odometer error.
- The alternatives table lists plus-size and minus-size options with a diameter close to your current tire. You can change the allowed tolerance.
How to read a size
Take 225/45R17 94W as an example:
| Part | Meaning | Value |
|---|---|---|
| 225 | section width | 225 mm |
| 45 | aspect ratio (sidewall height as a share of width) | 225 x 45% = 101.25 mm |
| R | radial construction (ZR marks a high-speed tire) | |
| 17 | wheel rim diameter | 17 in (431.8 mm) |
| 94 | load index | a higher number carries more load |
| W | speed symbol | rated up to 270 km/h |
Overall diameter (mm) is rim diameter (in) x 25.4 + 2 x sidewall height. For 225/45R17 that is 431.8 + 202.5 = 634.3 mm (about 24.97 in), a circumference of about 1,993 mm and about 501.8 revolutions per km.
Example
| Item | 225/45R17 (current) | 245/40R18 (new) |
|---|---|---|
| Sidewall height | 101.3 mm | 98.0 mm |
| Overall diameter | 634.3 mm | 653.2 mm |
| Circumference | 1,993 mm | 2,052 mm |
| Revolutions per km | 501.8 | 487.3 |
The diameter grows by 18.9 mm, or +2.98%. With the new tires, when the speedometer reads 60 km/h you are really going 61.8 km/h, at 100 km/h it is 103.0 and at 120 km/h it is 123.6. When the odometer shows 100 km you have actually covered about 103.0 km.
Going from 225/45R17 to 205/55R16 gives 631.9 mm, 2.4 mm smaller (-0.38%). Sizes with a similar diameter (tolerance 1.5%):
| Rim | Size | Diameter | Difference |
|---|---|---|---|
| 16 in | 255/45R16 | 635.9 mm | +0.25% |
| 16 in | 205/55R16 | 631.9 mm | -0.38% |
| 17 in | 205/50R17 | 636.8 mm | +0.39% |
| 18 in | 255/35R18 | 635.7 mm | +0.22% |
| 19 in | 215/35R19 | 633.1 mm | -0.19% |
Things to know
- A diameter difference within +/-3% is a commonly quoted guideline for tire changes, not a legal limit. The sizes approved by your vehicle manufacturer take priority.
- A larger diameter makes the speedometer read lower than your real speed; a smaller one makes it read higher. Speed enforcement uses the real speed.
- The tool does not judge wheel rim width, fender or suspension clearance, or whether the load index and speed symbol are sufficient. The alternatives table only matches diameter.
- The result is for a new tire. Wear reduces the diameter, and pressure and load change it slightly.
- Results are a reference calculation.
Convert speeds with the speed converter and mm to inches with the length converter. For vehicle value and running cost, try the used car depreciation calculator and the fuel cost calculator.
FAQ
How do I read the numbers on a tire?
The first three digits are the section width in mm, the two digits after the slash are the aspect ratio in percent, and the number after R is the rim diameter in inches. A trailing number and letter are the load index and speed symbol.
Does a plus-size change the speedometer?
Not if the overall diameter stays almost the same. The usual method is to lower the aspect ratio while widening the tire so the diameter matches, and the alternatives table lists such candidates.
Is a difference above 3% acceptable?
Beyond the common guideline the speedometer error exceeds 3% and you may run into wheel arch clearance or transmission and ABS calibration issues. Check that the size is approved by the manufacturer.
Can the front and rear sizes differ?
Some vehicles use different front and rear sizes. This tool compares one size at a time, so calculate each axle separately.
Is my input stored?
No. Everything is calculated in your browser and never sent to a server.