1. Home
  2. Audio & Subtitles
  3. Audio Editor & Converter

Audio Editor & Converter

Open an audio file, stack editing steps and save once in the format you need.

Runs in your browser · No upload
Open an audio file to see its waveform, then stack steps below and save once.
Your file is processed only in this browser and never sent to a server.

How to use

  1. Drop an MP3, WAV, M4A, OGG or FLAC file onto the box, or click to open one. You’ll see its format, length, sample rate, channels, an estimated average bitrate (file size divided by length) and the waveform.
  2. Under Add a step, stack whatever you need: trim, fade, volume, speed and pitch, reverse, remove silence, mono/stereo, sample rate. Steps run from the top down, and you can reorder, turn off or delete them.
  3. Use the Original / Result switch and the play button to listen. Click the waveform to play from that point, or select a range to play just that part.
  4. Under Save, pick a format and bitrate to see the estimated size. Saving downloads a new file such as name_edited.mp3. To change the format only, save without adding any steps.

Steps

Step What it does Default
Trim Select a range on the waveform and keep it or delete it. ←/→ moves a handle by 0.1 s Whole file
Fade in / out Ramps the volume up at the start and down at the end (linear or exponential) 1 s / 1 s
Volume Peak normalize, loudness (LUFS) normalize, or a fixed dB change −14 LUFS
Speed & pitch 0.5 to 2× speed (pitch kept), −12 to +12 semitones, or both together like tape 1× / 0
Reverse Plays the sound backward n/a
Remove silence Finds quiet parts, cuts them and joins the rest −45 dBFS, 0.5 s, 0.1 s margin
Mono / stereo Mix down to mono, copy mono to both sides, swap left and right, or keep one channel n/a
Sample rate Converts to 44.1, 48, 22.05 or 16 kHz 44.1 kHz

Output formats compared

Format Type Notes
MP3 Lossy Plays almost everywhere. 64 to 320 kbps, constant bitrate
M4A (AAC) Lossy Usually sounds better than MP3 at the same bitrate. Needs your browser’s AAC encoder
OGG (Opus) Lossy Holds up well at low bitrates, good for speech. Needs your browser’s Opus encoder
WAV Lossless, uncompressed Large files. 16-bit, 24-bit or 32-bit float
FLAC Lossless, compressed Opens if your browser can read it, but saving isn’t supported. Use WAV for lossless output

The estimated size is bitrate × length. These figures are for 3 minutes of 44.1 kHz stereo.

Setting Estimated size
MP3 192 kbps 4,320,000 bytes
MP3 128 kbps 2,880,000 bytes
MP3 64 kbps 1,440,000 bytes
AAC 128 kbps 2,880,000 bytes
Opus 96 kbps 2,160,000 bytes
WAV 16-bit 31,752,044 bytes

To make a file smaller, lower the bitrate, switch stereo to mono, or, for speech, drop the sample rate to 16 kHz. Saving an MP3 as MP3 again applies lossy compression a second time, so convert from the original if you still have it.

Loudness (LUFS) and normalizing

Peak normalizing sets the loudest sample to a target (−1 dBFS by default). A signal that peaks at 0.5 needs +5.02 dB to reach −1 dBFS. But the peak isn’t how loud something sounds.

Loudness normalizing measures something closer to what people hear, following ITU-R BS.1770. The audio passes through a K-weighting filter, is split into 400 ms blocks and averaged. Blocks below −70 LUFS, and blocks more than 10 LU below the average, are left out to give the integrated loudness. These values were checked by running the tool:

  • A 1 kHz sine at 0 dBFS in one channel: −3.0 LUFS
  • The same sound in both channels: about 0.0 LUFS (the two channels add up, +3 LU)
  • A −20 dBFS stereo sine: −20.0 LUFS. Normalizing it to −14 LUFS adds +5.99 dB

Targets differ by service. −14 LUFS is commonly quoted for streaming, −16 for podcasts and −23 for broadcast (EBU R128), but platform policies change, so check the guidelines wherever you upload. If the gain pushes the peak past −1 dBFS, a simple hard limiter clips it and you’ll see a warning. It isn’t a true-peak limiter, so the result can sound harsh.

How speed and pitch work

Speed (pitch kept) uses WSOLA. The audio is cut into 25.6 ms pieces and overlapped again, at whichever position lines the waveforms up best, to reduce glitches. A 2-second 1 kHz sine at 2× becomes 48,000 samples (1.0 s) and stays at 1,000 Hz. At 0.5× it becomes 4.0 s.

Pitch first shifts the pitch by resampling, then WSOLA brings the length back to the original. A 500 Hz tone raised 12 semitones becomes about 1,000 Hz and stays 2 seconds long. 440 Hz raised 7 semitones gives 659.4 Hz, close to the theoretical 659.26 Hz.

Together mode only resamples, so speed and pitch change together, like speeding up a tape: at 2×, 500 Hz becomes about 1,000 Hz. Stretching can add a slight echoey quality, and more so at extreme settings.

An example workflow

For cleaning up a recording, this order works well: remove silence → loudness normalize → MP3 128 kbps.

For example, take 1 second of a 440 Hz tone at 0.05 amplitude, 1 second of silence, then the same tone again (3 seconds in total). Remove silence with a 0.1 s margin, then normalize to −16 LUFS. The result is 2.2 seconds long and measures −16.0 LUFS. The silence is detected at 1.000 to 2.000 s, and with a margin of 0 the result is 2.0 s. You can type times as 1:02.500 or 62.5; both mean 62.5 seconds.

Limits and notes

  • You can open files up to 500 MB and 1 hour long. One hour of 48 kHz stereo takes about 1.4 GB as floating-point data. Longer audio, or audio that would need more than about 1.5 GB of memory, is refused. Over 30 minutes, you’ll get a notice that things may be slow.
  • For files with three or more channels, only the first two are used.
  • If the browser’s built-in decoder opened the file, the sample rate may have been changed to your device’s default. A notice tells you when that happens.
  • Saving as M4A or OGG uses your browser’s WebCodecs audio encoders. If they’re missing, you’ll be told why and pointed to MP3 or WAV. MP3 adjusts some sample rates and bitrates to fit the encoder’s limits (up to 160 kbps below 32 kHz).
  • Processing and encoding run on a separate thread, so the page stays responsive and you can cancel at any time.

Your file is processed in your browser and never sent to a server.

Can't find the tool you need?

Tell us what you want to do. We build the most requested tools first.