1. Home
  2. Audio & Subtitles
  3. Noise Meter (Microphone)

Noise Meter (Microphone)

Check how loud it is around you with a live relative dB reading.

Runs in your browser · No upload
This is an uncalibrated relative value. Microphone sensitivity differs by device, so it can differ from a real dB(A) meter and must not be used as legal evidence or for safety decisions. Use it to compare which sound is louder.
Microphone idle
dB
Match it against a real sound level meter. Changing it resets the readings.

Sound is never recorded or sent anywhere. Only its level is calculated.

Current level (relative dB)
-- dB
 
Min
-
Average (energy mean)
-
Max
-
Last minute

How to use

  1. Press Start measuring and allow microphone access when the browser asks.
  2. The big number is the current relative dB. A bar and a loudness band show roughly how loud it is.
  3. Min, average and max cover the time since you started, and the graph shows the last minute.
  4. Press Stop when you are done. Reset readings clears the record.

Sound is never recorded or sent to a server; only its level is calculated in the browser.

Please note: this is an uncalibrated relative value

The dB shown here is not the same as a real sound level meter reading. A meter has a calibrated microphone and applies A-weighting to mimic human hearing. Phone and laptop microphones differ in sensitivity from device to device, and no A-weighting is applied here. So use it like this:

  • Good for: comparing whether today is louder than yesterday, or which of two rooms is quieter
  • Not suitable for: legal evidence, complaints, workplace safety decisions, or checking hearing-protection limits

For disputes or safety questions, use a calibrated meter or ask a qualified professional.

How the number is calculated

  1. The root mean square (RMS) of the microphone signal is computed.
  2. It is compared with a full-scale signal (1.0) as 20 × log10(RMS). This is always 0 or below and is measured in dBFS.
  3. The calibration offset (90 dB by default) is added and the result is shown in a 0 to 130 dB range.
Signal RMS dBFS Shown with default offset (+90)
1.0 0 90 dB
0.5 -6.0 84.0 dB
0.1 -20 70 dB
0.01 -40 50 dB

Doubling the signal adds about 6 dB. The average is an energy average, not a plain average of dB values. For example, the average of 60 dB and 70 dB is about 67.4 dB rather than 65, because the louder moment dominates the energy.

While measuring, the browser’s echo cancellation, noise suppression and automatic gain control are turned off so the reading is neither squashed nor inflated.

Matching the offset to a real meter

If you have a sound level meter or a meter app, compare both readings for the same sound and adjust the offset. If this tool shows 62 dB where the meter shows 55 dB, lower the offset by 7, from 90 to 83. This only matches near that loudness; at other levels the error can differ. Changing the offset clears the readings.

Typical sound levels

These are commonly quoted approximate values and depend on distance and surroundings.

Approx. dB Example
30 Whisper, quiet bedroom
40 Library
60 Normal conversation
70 Vacuum cleaner, busy road
85 Level where long exposure calls for hearing care (the US NIOSH recommended limit is 85 dB(A) over 8 hours)
100 Construction site, motorcycle
110 Concert

FAQ

I allowed the microphone but nothing happens.

Check that the site’s microphone permission is allowed in the browser and that no other app is using the microphone. Also confirm the correct input device is selected in your system settings.

The number is far from my real sound meter.

That is expected. Microphone sensitivity, distance and reflections vary, and no A-weighting is applied. Use it for comparison, or match it to one sound with the offset above.

Can I use it as evidence of noise from neighbors?

Official limits apply to measurements from calibrated equipment. The values here are for reference only and cannot serve as evidence. Use it to note the times when noise recurs, and follow the proper measuring procedure of the relevant authority for disputes.

Is my sound recorded or uploaded?

No. Only the level is calculated; nothing is recorded or sent. If you need a recording, use the online voice recorder.

I want to clean up or even out the sound.

For background noise in a recording, try audio noise reduction, and to level the volume use audio normalize. Microphone input is processed in the browser only and never sent to a server.

Can't find the tool you need?

Tell us what you want to do. We build the most requested tools first.