How to use
- Type the port number to check, or tap one of the common port chips (22 SSH, 80 HTTP, 443 HTTPS, 3389 RDP, 25565 Minecraft, 8080, 3306 MySQL and more).
- Press Check port on my IP. Nothing runs when the page opens or when you change the number. The server makes one connection attempt only when you press the button.
- The result shows your public IP, the port state (open, closed, filtered or could not check) and the time taken, along with what the state means and what to do next.
- Command examples for opening the port in a firewall and for checking whether something is listening appear below the result, already filled in with your port number.
This is not a tool for looking up other people’s IPs or servers. The server only checks the port on the public IP of whoever is using this page. There is no field for a target address, and it is not a port scanner. It is for verifying that your own router and firewall setup works.
What the four results mean
| State | Meaning | Next step |
|---|---|---|
| Open | A connection to that port on your public IP succeeded. Nothing blocks it and a program is listening | Confirm you meant to expose it, otherwise stop the program or remove the rule |
| Closed | The request reached your IP but the connection was refused | Check that the server runs, the forwarding rule and the internal IP |
| Filtered (no response) | No reply at all. A firewall or router may be dropping packets | Check the device firewall, the router and cloud security groups |
| Could not check (error) | The state could not be determined. Different from open or closed | Turn off VPN or WARP and retry, or test from another network |
When port forwarding does not work
- Is the server program running? A port only shows as open if a program is listening on it. If nothing is, the result is closed no matter how well the firewall and router are set up. On Linux use
ss -tlnp | grep ':8080 ', on Windowsnetstat -ano | findstr :8080. - Device firewall. On Ubuntu run
sudo ufw allow 8080/tcp. On Fedora or RHEL runsudo firewall-cmd --permanent --add-port=8080/tcp && sudo firewall-cmd --reload. On Windows runnetsh advfirewall firewall add rule name="Port 8080" dir=in action=allow protocol=TCP localport=8080. Replace 8080 with your port. - Router port forwarding. Log in to the router admin page (usually the gateway address, such as 192.168.0.1 or 192.168.1.1) and find the port forwarding menu (sometimes called virtual server or NAT). Set the external port, the internal IP, the internal port and the protocol (TCP or UDP). Give the device a fixed address through a DHCP reservation so the internal IP does not change. The subnet calculator helps if you are unsure about your internal range.
- Where you test from. Connecting to your own public IP from inside the same network can fail on some routers (no hairpin NAT), so the outside view this tool gives is more reliable.
Limits and cautions
- It only tests whether a TCP connection can be made. UDP ports (some game servers, WireGuard) cannot be judged this way.
- Carrier CGNAT and double NAT. If your ISP puts many customers behind one public IP, or there is another router in front of yours, the public IP this tool sees belongs to the carrier, not your router. Then the port always shows as closed however you forward it. An IP between 100.64.0.0 and 100.127.255.255 means CGNAT for certain. If your router’s WAN IP differs from what What Is My IP shows, suspect it.
- Only the IP version used for the connection is checked, IPv4 or IPv6. If you came in over IPv6, IPv4 ports are not covered. See IPv6 check for your connection.
- With a VPN, Cloudflare WARP or a proxy, the exit IP becomes the target, so you would be testing the VPN server instead of your router. Turn it off first. Addresses on the Cloudflare network cannot be connected to and may give an error.
- The attempt has a time limit, and requests are limited to 6 per minute per IP.
- The result is a snapshot. It changes when you start or stop the server program.
Security check for open ports
An open port means anyone on the internet can try to reach that program. Ports such as 3389 (remote desktop), 3306 (MySQL), 5432 (PostgreSQL), 6379 (Redis), 445 (SMB) and 23 (Telnet) are favorite targets of brute force attacks and vulnerability scans, so the rule is not to expose them to the whole internet. If you must, limit the allowed source IPs or use them only inside a VPN. For 22 (SSH), disable password login and use keys only; the SSH config generator can help with the client side. For a web server, keep the software updated, block unneeded admin pages and use HTTPS. If this tool reports a port as open that you did not intend, stop the program and remove the router forwarding rule and the firewall allow rule.
What is sent to the server
The only input is a port number, and it is the only thing sent. The server reads the IP of the requester itself, tries to connect to that port on that IP and returns the result. Nothing is stored, and nothing is kept in your browser’s localStorage. This is not a tool for scanning someone else’s IP or service, or for causing load.
Frequently asked questions
How do I check whether my port is open?
Enter the port number and press the button. Start the program that uses that port first. It only shows as open when something is listening, and a stopped program means closed even if the firewall is open.
Can I check another person’s IP or domain?
No. The tool only checks the public IP of the person using it, and there is no address field. It cannot be used for port scanning. To see which IP a domain points to, use DNS lookup.
I set up port forwarding but it still says closed.
Check, in order, that the server program is running, the device firewall, and the router’s internal IP and protocol. If all of that is right, CGNAT or double NAT is the likely cause. Ask your ISP about a public IP, or use a VPN or tunnel instead.
What is the difference between open, closed and filtered?
Open means a connection was made. Closed means the request reached the IP but was refused. Filtered means there was no reaction at all, so a firewall is probably dropping packets. For security, filtered reveals less about your machine than closed.
How do I check a Minecraft server port?
Tap the default 25565 chip and check. If the server is running and TCP 25565 is forwarded to its PC, you will see open. For the quality of your connection itself, see the internet speed test.
Where can I see my IP and location?
The IP in the result is the public IP used for the check. Location and ISP details are in What Is My IP and IP geolocation.
The port number you enter is sent to a server only to run the check and is never stored.