1. Home
  2. Images
  3. Adjust Photo Brightness & Filters

Adjust Photo Brightness & Filters

Tune a photo with sliders and filters, compare before and after, then save.

Runs in your browser · No upload

How to use

  1. Drop photos on the page or click to choose them. With several photos, the first one is shown as a preview so you can tune the settings once and apply them to all.
  2. Click a filter or move the sliders. After picking a filter you can keep fine-tuning with the sliders. Double-click a slider to reset it to 0.
  3. Hold Hold to see the original to compare before and after, and check the tone distribution in the histogram below.
  4. Choose a format and quality, then press Build the file to compute the result at the original resolution. If you change a setting, build it again.

Adjustments

Control Range What it does
Brightness −100 to +100 Adds or subtracts the same amount from every pixel value. +100 is +128
Contrast −100 to +100 Widens or narrows the gap between light and dark around the midpoint 128. −100 makes everything gray; +100 multiplies the gap by 2.5
Saturation −100 to +100 −100 is black and white (R=G=B); +100 moves each color twice as far from its brightness
Exposure −100 to +100 ±100 is ±2 EV. 50 is 1 EV, which doubles pixel values
Temperature −100 to +100 Blue ↔ yellow. +100 is R +30, G +10, B −40
Tint −100 to +100 Green ↔ magenta. +100 is R +15, G −30, B +15
Highlights −100 to +100 Affects only bright areas, up to ±64
Shadows −100 to +100 Affects only dark areas, up to ±64
Sharpen 0 to 100 Unsharp mask: boosts the difference from a blurred copy to bring out edges
Vignette 0 to 100 Darkens the corners. At 100 the corners are black
Blur 0 to 20 px Box blur, measured in pixels at the original resolution

Adjustments are applied once each in this order: exposure → brightness → contrast → highlights and shadows → temperature and tint → saturation → black and white and sepia → blur → sharpen → vignette. The preview and the saved file use the same order and the same math, so what you see is what you get. For example, brightness +50 turns gray 128 into 192, and contrast +100 turns a pixel value of 100 into 58 and 150 into 183.

Filters

Filters are bundles of slider values, so after you pick one its values show up on the sliders.

Filter Made of
B&W Convert to black and white
Sepia Sepia 100
Vintage Sepia 35, contrast −10, saturation −15, temperature +20, vignette 35, brightness +5
Vivid Contrast +15, saturation +30, sharpen 30
Warm Temperature +35, tint +5, saturation +5
Cool Temperature −35, tint −3
High-contrast B&W Black and white, contrast +45, brightness −5
Faded film Contrast −25, saturation −25, brightness +10, shadows +40, temperature +8

Auto enhance and the histogram

A histogram counts pixels in 256 brightness bins from 0 to 255. If the graph is piled up on one side the photo is dark or bright; if it sits in the middle only, contrast is low. Auto enhance finds the 0.5% and 99.5% points of the brightness distribution, sets contrast and brightness so that range stretches toward 0–255, and raises saturation by 10. Ignoring the outermost 0.5% on each end keeps a single speck from skewing the result. Contrast tops out at +100, so a very narrow range (say 100 to 140) is not stretched all the way in one go: it gets contrast +100 and brightness +16, which widens the range by about 2.5 times.

Why black and white uses a weighted average

Black-and-white conversion and saturation use 0.2126×R + 0.7152×G + 0.0722×B for brightness rather than a plain average (R+G+B)÷3, because the eye is most sensitive to green and least to blue. Pure red becomes 54, green 182 and blue 18. A plain average would turn all three into 85 and erase the brightness difference between green grass and blue sky.

Good to know

  • JPG is compressed again every time it is saved and loses a little quality. Keep your original and make all adjustments from it in one go.
  • Pushing a photo too far (brightness, exposure or contrast near +100) turns bright areas pure white and the detail cannot be recovered. A spike at the right end of the histogram means detail is clipped.
  • Sharpen and blur are scaled to the photo size so the preview (up to 1200 px) and the saved file look alike.
  • Photos beyond 8000 px on the long edge or 40 megapixels are shrunk by default. Turn that option off to process at full size if your browser allows it, but it may be slow or fail.
  • To cut a photo use Crop Image, to change dimensions use Resize Image, and to reduce file size use Compress Image.

Your files are processed only in your browser and are never sent to a server.

Can't find the tool you need?

Tell us what you want to do. We build the most requested tools first.