1. Home
  2. Barcode & Generate
  3. A4 Label Sheet Printer

A4 Label Sheet Printer

Fill label sheets with barcodes, QR codes and addresses, then fine-tune print offsets.

Runs in your browser · No upload
1. Label sheet

2. Content
In list mode you can use {column} placeholders.
Multiple lines allowed. In list mode you can use {column} placeholders.
pt
5–72
Copy columns from a spreadsheet or use commas. The first row names the columns used as {column} above.
Labels printed per row

3. Cells | reuse a partly used sheet
123

Starts at cell 1. Start and skip only apply to the first sheet.

First label
Cookies Chocolate
Labels
3
Sheets needed
1
Cells per sheet
21

4. Print alignment

Printers drift a little. Print the test page on a real label sheet and enter the error you measure.

mm
±10 mm in 0.5 steps (positive = right / down)
mm
±10 mm in 0.5 steps (positive = right / down)
%
90–110%, 0.1 steps
Saves the values per name in this browser.

5. Output
Print at "Actual size (100%)" and set the paper type to labels. "Fit to page" will shift the cells.

Your text and images are processed in your browser only and never sent to a server.

How to use

  1. Choose a label sheet layout. Find the one that matches your sheet by cell count and label size (for example A4 21 labels, 63.5×38.1 mm). If none matches, pick “Custom” and enter columns, rows, label size, margins and gaps. If the values run past the paper, the reason is shown straight away.
  2. Set the content. A quick template (text, barcode + text, QR + text, address label) fills in an example table you can edit. Text and barcode values can use {column} placeholders.
  3. In list mode, paste columns copied from a spreadsheet. The first row names the columns and every following row becomes one label. Raise “Copies” to print the same label several times.
  4. Use cell selection to reuse a partly used sheet. Click a cell to make it the start cell, and mark cells that were already peeled off with “toggles skip”.
  5. Press Create PDF, and print it at actual size (100%).

Label types

Type Layout inside the cell
Text Text fills the cell. If it does not fit, the font shrinks in 0.5 pt steps down to 5 pt
Barcode One barcode filling the cell
Barcode + text Barcode in the top 60%, text below
QR code One QR code filling the cell
QR + text QR on the left and text on the right when the cell is wide, otherwise QR above and text below
Image (logo) + text Logo on top, with text below when there is any

Barcodes use the same types as the Barcode Generator, including EAN-13, UPC-A, Code 128, GS1-128 and Data Matrix. For EAN, UPC and ITF, a value without its check digit (such as 12 digits for EAN-13) gets the check digit added automatically. Rows with a bad value are listed with the row number and the reason, and the PDF is not created until they are fixed. Text that a PDF standard font cannot draw, such as Korean, is drawn as an image so it shows correctly in any viewer.

Measuring your label sheet

If no preset matches, measure with a ruler: the width and height of one label, the distance from the top edge of the paper to the top of the first row (top margin), from the left edge to the left of the first column (left margin), and the gaps between labels, horizontally and vertically, in millimetres. Enter them under “Custom” and check the preview against the real sheet.

Presets are named by cell count and size, not by product number. Sheets with the same label size can still differ by a few millimetres in margin between makers, so confirm with the calibration page first. For example A4 21 labels (63.5×38.1 mm) is 3 columns by 7 rows with a 7.25 mm left margin, a 15.15 mm top margin and a 2.5 mm horizontal gap, so the top-left corners of the first three cells sit at 7.25 mm, 73.25 mm and 139.25 mm from the left edge.

Fixing print offsets

Printers feed paper slightly off, or scale the page a little. Tune it like this:

  1. Download the “Calibration test page (PDF)” and print it on plain A4 paper at actual size (100%).
  2. Lay the printout over a label sheet against the light and measure, in millimetres, how far the cell outlines and centre crosses are from the real label cells.
  3. If the crosses land to the left of the label centres, enter a positive value for horizontal shift (for example +1.5); if they land too high, enter a positive vertical shift. Shifts range over ±10 mm in 0.5 mm steps.
  4. Measure the full width from the left edge of the first column to the right edge of the last one and compare it with the design width. For A4 21 labels the design width is 3×63.5 + 2×2.5 = 195.5 mm; if your printout measures 193.5 mm, the scale is 195.5 ÷ 193.5 × 100 = 101.0% (one decimal place, 90–110% allowed).
  5. Enter the values and check again with the real label PDF. Type a printer name and press “Save values” to store them in this browser for next time. If the browser blocks storage, nothing is saved and you can simply type the values again.

Printer settings and partly used sheets

  • In the print dialog choose Actual size / 100% and turn “Fit to page” off. With it on, every cell shifts.
  • If your printer has a paper type setting (labels, heavy paper and so on), set it to match the sheet. Feeding differs between printers and paper types, so check your offsets again after changing it.
  • For a partly used sheet, use the start cell and skipped cells. Printing 30 labels on A4 21 labels, starting at the 3rd cell and skipping the 6th, puts 18 labels on the first sheet and 12 on the second, so you need 2 sheets. Start and skip apply to the first sheet only; the second sheet uses every cell.
  • You can make up to 2,000 labels at a time.

To make lots of barcodes as files, use the Barcode & QR Bulk Generator. For a single styled QR code, see the QR Code Generator. To change the paper size of a PDF, use Resize PDF Paper.

Your text and images are processed in your browser only and are never sent to a server.

Can't find the tool you need?

Tell us what you want to do. We build the most requested tools first.